Common problems and solutions of diamond saw blades

  Diamond saw blade is a cutting tool, which is widely used in the processing of hard and brittle materials such as concrete, refractory materials, stone materials, and ceramics. The diamond saw blade is mainly composed of two parts; the base body and the cutter head. The base body is the main support part of the bonded cutter head.

The cutter head is the part that cuts during use. The cutter head will be continuously consumed during use, but the matrix will not. The reason why the cutter head can cut is because it contains diamond, and diamond is the most important part. A hard substance that rubs and cuts the workpiece in the cutter head. The diamond particles are wrapped by metal inside the cutter head.

There are often some problems in the use of diamond saw blades. How to solve these problems?

1. The thickness of the cut sheet is uneven

(1) The basic tension is not suitable; the saw blade tension needs to be re-corrected.

(2) The screw of the fixed trolley screw bearing seat is loose; adjust the rotating screw.

(3) The diameter of the guide rail is poor in levelness; the suspected degree of disease detected by the method of pulling the wire is adjusted between 0.5mm, and the levelness should be less than 1mm.



(4) The clearance between the screw and the nut is large, and the operation does not eliminate the clearance; during operation, pay attention to eliminating the clearance in one direction.

(5) The phenomenon that the nut is not clamped tightly and shakes again; tighten the clamping nut.

(6) The guide pulley is inconsistent; loosen the nut and re-adjust the same.

(7) The end of the saw blade is too large; level the saw blade and pass the inspection.

(8) The welding of the cutter head and the base body is asymmetric; re-weld or replace the saw blade.

(9) The cut blocks are less than 0.5 cubic meters; the blocks should be larger than 0.5 cubic meters.

(10) The drive chain is too loose; adjust the chain tightness.

2. Excessive shaking during machine operation

(1) The main bearing clearance is too large; open the iron cover of the spindle box to adjust the nut.

(2) The spindle bearing is damaged, causing the saw blade to run erratically; disassemble the spindle box to check the spindle bearing and replace it with a new one.

(3) The radial runout of the saw blade is too large; check the radial runout of the saw blade and change the blade.

3. The height of the saw blade is inconsistent after use

(1) The clearance of the spindle bearing is too large; open the iron cover of the spindle box to adjust the nut.

(2) The accuracy of the diameter skipping the large center hole is out of tolerance; check and replace the saw blade.

To learn more

评论

发表评论

此博客中的热门博文

How Waterproof Is My Rain Coat: What Does 5000mm Mean?

图片
  If you are buying yourself a new   waterproof rain coat   and you're not too well versed in the ins and outs of modern day waterproofing technology, you may find yourself coming across a few rather confusing terms. What on earth does 5000mm mean? And 5000gsm? What's the difference? These are just a few of the questions that will be running through your mind.   Not to worry, our guide to waterproof technology is here to help. Number, Numbers, Numbers. But What Do They All Mean?   A waterproof garment is measured with two numbers. The first one measures how waterproof the  raincoat  is. This is measured in millimetres. You will see numbers from 2,000mm up to 8,000mm across our collection to describe to the consumer how dry the coat will keep you. But what does it mean? For example, if a coat were 5,000mm waterproof, a test is conducted where a long tube is placed over the fabric and the tube is then filled with water. 5,000mm or 5 metres (16.4 ft) is how far you could fill the
阅读全文

How does a Sweeping Robot Work?

图片
 A  sweeping robot  works by autonomously navigating and cleaning floors using a combination of sensors, motors, and advanced algorithms.  The Foundation of Sweeping Robots The concept of automated cleaning dates back to the late 20th century when the first robotic vacuums were introduced. These early models relied on basic bump-and-turn mechanisms to navigate. Over the years, advancements in  technology  have drastically improved the functionality and efficiency of these devices. The VIGGO sweeping robot stands at the forefront of this evolution, showcasing the latest innovations in robotic cleaning. How VIGGO Sweeping Robot Works Intelligent Navigation The VIGGO sweeping robot uses a combination of sensors to detect and avoid obstacles, ensuring smooth navigation around furniture and other objects. Infrared sensors help it to avoid collisions, and cliff sensors prevent it from falling down stairs. VIGGO’s advanced models utilize LIDAR technology to create detailed maps of their surro
阅读全文

5 Key Advantages of Sand Storage Hoppers

图片
Sand storage hoppers are integral to various industries, offering streamlined solutions for material management and storage. Whether in construction, agriculture, or manufacturing, these hoppers provide numerous benefits that enhance productivity and operational efficiency. Let's explore five advantages of utilizing sand storage hoppers:   Optimized Storage Capacity: Sand storage hoppers   offer ample space to store large quantities of sand efficiently. With their spacious design, these hoppers enable businesses to maintain sufficient sand reserves on-site, reducing the need for frequent refills and ensuring uninterrupted operations.   Enhanced Material Protection: Sand storage hoppers provide a protective environment for stored sand, shielding it from external elements such as moisture, contaminants, and UV radiation. This preservation of material quality extends the lifespan of the sand, minimizing waste and ensuring consistent performance in various applications.   Streamlined M
阅读全文